+ Enhanced Interior Gateway Routing Protocol (eigrp) Interview Questions and Answers, Question1: Does EIGRP support secondary addresses? Question2 . EIGRP Interview Questions and Answers. Networking Terms, Windows By Waqas Azam On January 7, No Comments. 17 Sep EIGRP Interview Questions. Description. EIGRP To sumarize: ip summary- address eigrp [AS] [IP] Reply – Used to answer a query (unicast).

Author: Voshicage Mezigore
Country: Iran
Language: English (Spanish)
Genre: Finance
Published (Last): 24 January 2007
Pages: 325
PDF File Size: 4.35 Mb
ePub File Size: 20.85 Mb
ISBN: 174-8-44891-501-9
Downloads: 30402
Price: Free* [*Free Regsitration Required]
Uploader: Gardashakar

The sia is caused by two sequential events: After 16 unacknowledged re-transmissions, the neighbor is eivrp from the neighbor table. The primary goal of routing protocols and routes is the construction of routing tables.

Successor Path and Feasible Successor path.

EIGRP Interview Questions and Answer | Online Networks Solution

Therefore, if all of the primary ip addresses of routers do not agree, problems can arise with neighbor adjacencies.

Explain Stuck in Active?

Disabling split horizon on the spokes radically increases EIGRP memory consumption on the hub router, as well as the amount eigrp interview questions and answers traffic generated on the spoke routers. An eigrp route can exist in one of two states, in the topology table: The protocol was designed by cisco systems as a proprietary protocol, available only on cisco routers.

No, only one route is installed. Without a neighbor adjacency, eigrp cannot exchange routes with a neighbor.

Advanced distance vector Routes eigrp interview questions and answers, ipx, decnet, appletalk Routing advertisements: It will reset the complete topology table. The local Router will clear the neighbor adjacency with any router s that has failed to Reply, and will place all routes from that neighbor s in an active state. Unequal cost load balancing in EIGRP is the concept by which load sharing can take place on paths that does not have the equal metric.

Related Posts (10)  2SK3561 PDF

It has to be same on participating neighbors. It sends a query when a route is eigrp interview questions and answers and another feasible route does not exist inside the topology table. The best path from the topology table will be copied in the routing table.

EIGRP Notes with Interview Questions

Reason is that it keeps feasible successor or Backup route in ready state and installs in routing table eigrp interview questions and answers successor fails.

Although eigrp does not send or receive routing updates on an interface configured with the passive-interface command, it still includes the address of the interface in routing updates sent out of other non-passive interfaces.

What does the neighbor statement in the eigrp configuration section do?

Router qurstions query packets to its neighbors asking them if they have information about this particular network. When the SIA occurs, the router clears the neighbor that did not reply for the query.

There is also a anewers eigrp interview questions and answers show commands that display neighbor table status, topology table status, and EIGRP traffic statistics.

Are you a person with commendable knowledge in computer networking? Report Attrition rate dips in corporate India: Eigrp sends a query when a route is lost and another feasible route does not exist in the topology table.

Shared Flashcard Set

What is Advertised distance? EIGRP maintain 3 tables. To influence the routing through the tunnel interface, It increases the bandwidth parameter of the tunnel interface, or increases the delay parameter of eigrp interview questions and answers VLAN interface. This is typically done at a redistribution point where two EIGRP autonomous systems are interconnected. Survey Most Productive year for Staffing: The following message is displayed by routers that run a supported release when a goodbye message is received: We can configure Inferview to understand whether it should attempt to use multicast facilities on a multi-access interface.

Related Posts (10)  ANSI Y32.2 PDF

Do this under the outbound interface on the eigrp interview questions and answers router with the ip summary-address eigrp Ansewrs 0. It nad classless in nature, supports multicast In order to disable the split horizon behavior, use the no ip split-horizon eigrp as-numberinterface command.

The neighbor command is used in eigrp in order to define a neighboring router with which to exchange routing information.

Cisco does not recommend running multiple EIGRP autonomous systems on the same set of interfaces on the router. How many paths can be load balanced answrs eigrp?

OSPF generates a default only if it is configured using the command default-information originate eitrp if there is a default network in the box from a different process. Routers do not form eigrp neighbors over secondary networks.

Eigrp redistributes default routes directly. Due to the current behavior of this command, eigrp exchanges routing information with the neighbors in the form of unicast packets whenever the neighbor command is configured for an interface.

Interview Question and Answer. What are the primary functions of eigrp interview questions and answers pdm? What types of authentication is supported by eigrp? Such path are called Successor. Eigep do you mean by Link State Protocol? Home About Us Eigrp interview questions and answers Q.

Acknowledgment packets are Unicast.